Home > News
News
-
Ningbo Qiaopu Electric Co., Ltd. plug molding operation precautions
Ningbo Qiaopu Electric Co., Ltd. plug molding operation precautions Ningbo Qiaopu Electric Co., Ltd. molding operation precautions: ⑴ the machine running your hands or other prohibited items into the mold. ⑵ not both simultaneously a machine to avoid accidents ⑶ prohibits hand or other body parts close to the operation of the machine parts. . ⑷ attention to the power cord color injection molding of plastic materials and note whether the color line drawings. ⑸ attention on the quality of a process, if any undesirable phenomenon, immediately superior to the Qiaopu reflect. ⑹ product must be self-removed, see to pick out bad products, and rework time, there are special problems need to the higher authorities. ⑺ emergency press the emergency stop switch. Second, the self-test method: A bit like the surface of the material, charred, silver, water lines, air bubble, deformation, lack of material, color, weld lines, flash, dislocation, color separation, wire crushed, exposed copper wire, wire, wire exposed too long or too short, shrink, mold using the wrong model, SR direction of the anti-, SR lifting is not enough; are ill. Third, machine maintenance: ⑴ timely repair of the faulty machine, and each day recorded in the maintenance and repair of "Qiaopu machine maintenance card." ⑵ always wipe the surface of machine oil, clean the table to keep clean. ⑶ every morning before starting the lubrication. [View Details] -
Qiaopu Electric employees travel the implementation details
Qiaopu Electric employees travel the implementation details (A) Qiaopu Electric employees on the need for official, was ordered to travel abroad (including Relocation) note in accordance with the provisions of this chapter. (B) Qiaopu electrical charge of each unit of travel are following orders or instructions, depends on the needs of qualified approval underwent general manager of the petition date. (C) Employees shall travel before departure, according to the style set by completing the form, notify the General group registered as a special case for less than the advance, the form should also bill the forgotten as soon as possible, sent to the registration. (D) staff travel was reported by actual travel expenses, the highest standards, such as schedule, except in special circumstances, approved by the general manager, the other over-reported if supported, should be removed it. (E) staff before a business trip, get travel advances according to the actual needs of its pre-borrowing, the head of the first instance by the petitioner after the approval of payment on account of the general manager, travel is completed, after poor sales to the General group should be written off within three days reported such as three days later, those who have not reported support, accounting group travel advances should be in the member's remuneration deducted under thoroughly, once reported that branch, the nuclear re-pay. (F) Qiaopu Electric employees in the city and suburbs or other on the same day to travel from the solid support by mistake to the transportation and meals. (G) employees travel in more than one day, travel day of their otherwise satisfied, regardless of departure or return date shall be paid half, and Cheng Ye car commuters, not the other branch hostel fee. (H) Transportation costs, including travel and other expenses that must be the journey, according to the actual reported expenditure, then other small incidental expenses with the fees are within the meal expenses may not be reported branch. (Ix) Where the public and special public keying of Posts and Telecommunications, temporary employment of people her husband, traveling expenses of other items are necessary expenses, other expenses in the column special report was supported by solid evidence. (X) Qiaopu Electric employees in addition to travel halfway sick and natural force majeure reasons, and that those who do leave shall not be arbitrarily changed the date, or extended travel time, but afterwards permitted by the general manager who was to ratify it. (K) employees of travel, should honestly make a receipt issued by, but if there is something false is not the truth, the collar will be recovered in addition to outside, and depending on the severity of the circumstances, won him punished. (L) pre-and post travel and staff travel should be completed in all forms and other formalities should be. [View Details] -
Qiaopu staff canteen regulations
Qiaopu staff canteen regulations (A) strictly abide by all rules and regulations Qiaopu company. Work on time, stick to work, obey the organization, failing to ask (sell) at, without consent are not allowed to leave work. (B) establish dedicated to the idea of serving staff, attention to professional ethics. Civilized service, affable, warm and active, courtesy, love of their own, seriously. So fragrant rice ready meal, delicious, food quantity, food enough to say, to treat people equally. (C) compliance with financial discipline. Qiaopu eat all employees receive (pay) meal tickets, banned cash. Kitchen staff required to pay the monthly payment on meals, strict registration procedures. Any person subject to the required standards in the canteen fees. Not allowed into the library have been sold out items. (D) adhere to the physical inspection system, improve cost accounting. Do Nissin statement, consistent with the account book. Inventory once a month, the monthly published regularly in early accounts, accept the supervision of staff. (E) caring for public property. Qiaopu canteen of all equipment, utensils are registered with the accounts, not petty, placed in public places on any object within the (public or personal), not just to make it move or take with. Undue damage to the various types of equipment, utensils, and they should according to the compensation price. (F) personal hygiene to do cooking. Do wash their hands, nails, frequently changes, wash clothes, work clothing and headgear to wear at work. Kitchen staff to conduct a health check every year, no health certificate who are not allowed to work in the cafeteria. (Vii) plans to purchase, purchase is strictly prohibited rotten, rotten food, prevent food poisoning. (H) arrangements for the staff dining Qiaopu line issues and reduce queuing time, time to open meal. To develop a recipe a day, breakfast, lunch and dinner to more varieties of style, to improve cooking techniques, improve employee meals. For those who need a temporary guest and can not eat meals on time, can make an appointment in advance and notification. (Ix) make security work. Use mechanical tools or cooking utensils to strictly abide by the rules to prevent accidents; prohibited comes with access to the kitchen and storage room; flammable and explosive materials to be placed in strict accordance with regulations, prevent accidents; canteen staff before work, To shut doors and windows, check the various types of power switches, and equipment. Administrators should always supervise, check and do security work. (J) strengthening management, unity, strict implementation of various Qiaopu rules and regulations, the successful completion of various tasks. [View Details] -
Ningbo Qiaopu Electric Co., Ltd. Guidelines for the Management of Health
Ningbo Qiaopu Electric Co., Ltd. Guidelines for the Management of Health 1. Ningbo Qiaopu Electric Co., Ltd. to maintain the health of employees and the workplace environment, health, tailor-made the final version of guidelines. (2) Where the Ningbo Qiaopu Electric Co., Ltd. health matters, except as otherwise provided, note the line in accordance with these guidelines. 3 The Company health issues, in addition to General and production units (Health and Safety Committee) is responsible for, the entire staff to be really one to follow. 4. Any new member must be aware of health into the importance and application of knowledge. 5. The workplace shall be maintained clean, no odor or impede the accumulation of sufficient health of the occurrence of garbage, dirt or debris. 6. Walkway within the workplace and the ladder, cleaning at least once a day, and to adopt appropriate methods to reduce dust emissions. 7. The workplace should be prohibited spitting. 8 drinking water must be clean. 9. Ningbo Qiaopu Electric Co.LTD toilets, toilets, changing rooms and other health facilities, must be particularly clean. 10. Drains should be kept clean dirty, clean and smooth. 11. Where parasitic infection bacteria may be the raw material should be disinfected before use to impose appropriate. 12. Who may have hindered health of gases, dust, powder of the work, shall comply with the following provisions: (1) using appropriate methods to reduce the production of harmful substances. (2) the use of closed equipment to prevent the dissemination of the harmful substances. (3) the occurrence of harmful substances in the last place, by their nature are as coagulation, sedimentation, to attract or exclude such disposal. 13. Who handle toxic substances or heat objects work or engaged in a dust, powder or toxic gases spread the work place, or exposure to harmful rays of the work to be with those who use protective clothing or equipment, should be the nature of the preparation. Staff engaged in the preceding paragraph, to the Company's equipment, protective clothing or equipment must be utilized. 14. Ningbo Qiaopu Electric Co., Ltd. lighting of the workplace, should be in accordance with the following provisions: (1) The department must have adequate light. (2) must have the appropriate light distribution. (3) the need to prevent the show off and flashing light. 15 of the Workplace window surface and the light part of the lighting equipment shall be kept clean, without rendering some masking. 16 Where the ladder, and lift up and down at the dangerous part of machinery required to have appropriate lighting. 17 The workplace should maintain an appropriate temperature, the temperature of the air-conditioning and ventilation adjusted to heating methods such as line of. 18. The workplace should be sufficient for air circulation. 19. Canteens and all the kitchen utensils and the environment, shall be kept clean. 20. Garbage, sewage, waste removal, etc., must meet health requirements, placed in boxes provided within the premises or may not be any accumulation of fly-tips. 21 The company should set up a kind of first aid equipment and medicines stored in a small box or small cupboard, placed clear of pollution prevention and convenient access to fine. Must be checked once a month, and its contents are missing should be added at any time. 22 The guidelines implemented after approval by the was, likewise modified. [View Details] -
Ningbo Qiaopu Electric Co., Ltd. identification card usage
Ningbo Qiaopu Electric Co., Ltd. identification card usage (A) to enhance site access control, to prevent loitering, etc. without the Ru Qiaopu electrical plant, to facilitate the identification, formulation of the rules. (B) Qiaopu appliances to work with identification cards are classified as follows: 1 Red: Management Department staff to wear. 2 yellow: Finance Department staff to wear. 3 light green: Sales Department employees to wear. 4 light blue: Planning Department staff to wear. 5 gray green: construction department staff to wear. 6 Green: Inspection room staff wear. (C) Qiaopu new staff settle into electrical plant procedures, identification cards issued by the personnel unit. (D) of the item identification cards, Qiaopu all electrical site all personnel wear the company for employees below the rank of managers wear. (E) Qiaopu electrical contracting officers requisitioned temporary identification cards as follows: 1 where the short-term contract work within 10 days of written notice by the unit in charge of guard and put deposit contracting the guard in exchange for personal identification badge to wear round, and identification cards handed in at the factory in exchange for ID cards. (2) Where more than 10 days longer-term contracting, made by the unit to send a list of photo identification cards of personnel units have requisitioned from the factory and handed in by the unit, short of loss if handled according to Article XII. (F) identification card shall be worn above the left chest on jacket, no coat to cover other identification cards, and offenders do not wear identification cards according to treatment, remove the identification card upon separation. (G) Qiaopu electrical identification card is lost, by written notice to the unit in charge of personnel replacement units, and withholding fee $ 15. Damage due to the public, may report to senior director of visa unit, the personnel unit recertification. . (H) identification card functions in the display department of the company associates the identity, so all staff at all levels should be worn if there is not the wearer and, if proved, the first warning, the second current entitlement to withhold one-third of the profit bonus of the amount, two-thirds of the amount of withholding the third, fourth after all the money that is withheld, the withholding of part of the notification by the personnel unit of the Ministry of Finance paid bonuses when the profits charged to (i) temporary Qiaopu electrical contracting officer not to wear, guards or factory management should notify the unit in charge of group is prohibited to factory work, or any accident, shall bear the full responsibility of the unit in charge of 2 and I out for improper use of identification cards of those violations. (J) where one of the following circumstances, be appropriate depending on the severity of punishment or dismissal and brought to justice. 1 identification card lending and non-colleagues out of the factory by the company. 2 identification cards to lend to others outside the perpetrators. (K) Qiaopu Electric employees during working hours, should wear identification cards according to requirements, methods likewise. (L) Upon approval of the rules was implemented after revision identification card recipients who likewise officers leave, the certificate should be handed in the personnel unit, or discount compensation of $ 100. [View Details] -
Ningbo Qiaopu Electric Co., Ltd. the management office and the Labor Insurance supplies
Ningbo Qiaopu Electric Co., Ltd. the management office and the Labor Insurance supplies Article: The purchase of office supplies made 1 month before the end of ministries, the department head room required to submit a plan of office supplies, general manager of the office; 2. Ningbo Qiaopu Electric Co., Ltd. General Manager's Office designate a person to develop a monthly budget plan and office supplies; approval by the competent Vice President responsible for office supplies purchased, according to the actual work to a planned distribution to various ministries, chamber. Signed by the department director to reclaim; 3 In addition to the normal ration of office supplies, if needed with other items subject to the General Manager's Office approval recipients; 4. Qiaopu's new staff of office supplies, office room under the Ministry responsible for a list of people and supplies inventory, responsible for fully serviced to ensure that new recruits to work; 5 responsible for the purchase of office supplies made of staff to do office supplies complete variety right path, and quantity high quality, inventory and reasonable expenses properly, take good care of supplies; 6. Responsible for purchases made to establish a personnel office supplies books, run out of warehouse procedures. The library must be signed by the receiving officer; 7 office supplies management must be civilized, clean, pay attention to safety, fire, theft, act in strict accordance with rules and regulations do not allow non-staff members enter the store. Article: Labor Insurance supplies purchase hair: Labor Insurance supplies rationed by the general manager's office under the ministries, the real work needs room to buy uniform, uniform. [View Details] -
Ningbo Qiaopu Conference Management essentials
Ningbo Qiaopu Conference Management essentials (A) improve the effectiveness of the meeting essentials Ningbo Qiaopu 1 to strictly observe the meeting start time. 2. In the beginning of the essence on the subject to do some simple instructions. 3. Turn the conference matters and the allocation of time for pre-order told the meeting. 4 during the meeting to note the following: (1) speech has deviated from the topic? (2) Ningbo Qiaopu speech whether for personal interest? (3) whether all the staff are attentive to speak it? (4) whether the speaker is too focused on some of the people do? (5) whether there had not spoken all the way through the people do? (6) whether a person's speech is too long then? (7) towards the conclusion whether the contents of speeches to promote it? 5 should lead to conclude within the scheduled time. 6 In the meeting time be extended, shall obtain the consent of everyone, and decided to extend the time. 7 should be sorting out the conclusion to all the staff vote to confirm. 8 should be implemented procedures to sort out the resolution, to be confirmed. (B) Ningbo Qiaopu meeting Contraindications 1 speak not long-winded, endless (in principle limited to 3 minutes) (2) can not be silent in the end from start to finish. 3. Not desirable to use incorrect information. 4. Do not expect to do talk about some of the predictions. 5 can not do personal attacks. 6. Not to interrupt the speech of others. 7. Can not pretend to understand, nonsense. 8. Not about abstract theory or idealism. 9. Can not be picky on speakers. 10 Do not leave half-way. [View Details] -
Ningbo Qiaopu Electric Co.LTD. power line industry-related terminology
Ningbo Qiaopu Electric Co.LTD. power line industry-related terminology Qiaopu power lines in the production process will encounter many things, such as current, voltage, power, stability, and other technical terms. Here we Ningbo Qiaopu Electric Co.LTD. met for the power cord under the profile industry related terms 1 rated current - performance under the normal conditions of use and high-voltage switchgear main circuit can carry the current value of continuous high-voltage switch equipment on test conditions. (2) Rated voltage - the use and performance of the prescribed conditions to the maximum continuous operation voltage, and it determines 3 Rated current Breaking current - under specified conditions, the normal circuit breaker to ensure the maximum short-circuit breaking current. 4 rated frequency - the required performance under the conditions of normal use and continuous operation of the grid frequency to the value, and it rated voltage, rated current to determine the high-voltage switch equipment on test conditions. 5. Rated peak withstand current (rated thermal current) - the use and performance of the prescribed conditions, the switch in the closed position can withstand the rated short time withstand current wave of the first half of the peak current. 6 Rated short time withstand current (rated thermal current) - the use and performance of the prescribed conditions, in determining the short period of time, the switch in the closed position can carry the provisions of rms current. 7. Rated short-circuit current - voltage and require the use and performance conditions, switch to the TV to ensure the normal short-circuit breaking current peak. 8 rated operation (lightning) impulse withstand voltage - when the pressure test, the equipment insulation can withstand the operation (lightning) impulse voltage of the standard value. 9 temperature - current switching device through various parts of the temperature and the ambient air temperature difference. 10 Power Factor (loop) - Switchgear switching test circuit equivalent circuit, under the frequency ratio of resistance and inductance, does not include the load impedance. 11 rated frequency withstand voltage - the conditions and time required to test the device's frequency withstand voltage standard value (RMS). 12 rated short-circuit duration (Rated dynamic time) - in co-location switch can carry the rated short time withstand current time interval. [View Details] -
Ningbo Qiaopu Electric Co., Ltd. telephone line management system
Ningbo Qiaopu Electric Co., Ltd. telephone line management system The first Ningbo Qiaopu Electric Co., Ltd. communications equipment and lines, maintenance work should strictly follow the Ministry of Posts and Telecommunications Administration of the city's telephone users on the relevant exchange management regulations. The second line of machine maintenance personnel should be familiar with and master Ningbo Qiaopu Electric Co., Ltd. using machine line equipment performance, structure and principles of testing, tuning and maintenance skills. In strict accordance with the Ministry of Posts and Telecommunications Directorate General of Telecommunications on the "technical maintenance standards and PHS subscribers switch cycle" provides a really good job machine line regular maintenance work. The third line of machine maintenance and traffic personnel should work closely together to make communications equipment, instruments, tools, keep clean and tidy, complete loss of integrity, good performance, operating normally. Article shall be responsible for organization and leadership × × timely preparation of annual, monthly maintenance of communications equipment line repair plan submitted to the competent authorities under the jurisdiction of balance, and organize staff to urge the timely completion of line maintenance machine maintenance program. Article machine line maintenance personnel should carefully prepare the original records of the daily accumulation of maintenance work, take good care and maintenance of communications equipment technical data. Main original records should include: 1 work diary; 2 obstacles records; 3 maintenance work plans (annual, monthly); 4 machine calendar card, the user card; 5 battery charge and discharge records; 6 other original records. Technical information should include: 1. The maintenance manual; 2 engine room electrical wiring diagram; 3 cable, strongyloidiasis, extension equipment layout; 4. Maintenance of records. Article Ningbo Qiaopu Electric Co., Ltd. phone units installed, demolition, should apply in writing to the × × by × × approved by the machine line maintenance personnel responsible for installation, demolition, relocation, and work orders issued internal collaboration, in real accounting of materials, cost of working hours, pay financial transfers. Article machine line maintenance personnel shall keep their whereabouts (Location) informed by telephone the total room for failure in communications equipment, can call at any time, as soon as possible. [View Details] -
Qiaopu electronics companies meeting management system
Qiaopu electronics companies meeting management system (A) General Provisions To improve the style, fewer meetings, shorter, increase its quality, Qiaopu special formulation of the electrical system. (II) classification and organization The first meeting grouped into four categories Qiaopu appliances: 1 plant-level meeting: including party leaders (the expansion) will, the whole plant cadres will, the whole plant group leaders will be, the whole plant members of the General Assembly, the whole plant members of the General Assembly, the factory workers of the General Assembly, the whole plant and a variety of technical staff will Congress. Were submitted to the party or the Factory should be approved by the party, government, workers, work groups, and other departments were responsible for organizing the meeting. 2 professional meetings: Department of whole plant of technology, business integration will be (such as analysis of business activities will, quality analysis, production and technical preparation will be, production scheduling, safety associations, etc.), led by the factory in charge of the approval of the competent business departments responsible for the organization. 3 system and the department will: the plant, department, branch of the work will be held (such as shop trade unions, scientific works will be, the branch will, workshops (sections) TUC, etc.) by the plant department, branch and is responsible for the leadership decided to convene organization. 4 team (team) will be: by the party, work, mission team leader or administrative decision and hosted group leaders. The second parent or other units in Qiaopu appliances meeting (such as spot, report, office meeting, etc.) or the plant will be the international business (such as joint venture talks, user forums, etc.) shall be accepted by the factory to do the arrangements, the business counterpart departments make the conduct of business collaboration. (C) the schedule of meetings Third regular meeting of the arrangements. Order to avoid the excessive or repeated, the whole plant of the meeting shall be included in the normal regular system, in principle, according to the routine specified time, place, content, organization meeting. Regular meeting as follows: 1 Chief Technology Conference (1) director's office: Research, deployment administration, to discuss and decide major issues in the administration of the whole plant. (2) Factory Service will: Summary evaluation of the administrative work of the production month, next month, arranged layout tasks. (3) more than group leaders and cadres of the General Assembly (or the whole plant TUC): Summarize the previous quarter (six months, year) work, deploy the season (half a year, New Year) tasks, recognition awards advanced collectives and individuals. (4) analysis of business activities will be: Reporting, analysis Qiaopu electrical implementation of the plans and results of operations, evaluation of various aspects of the work, positive results, exposing contradictions, suggest improvements to continuously improve the plant cost. (5) quality analysis: Report, concluded last month, the quality of the product, the quality of discussion and analysis of incidents (problems) to study the decision to quality improvement measures. (6) security work will be (including security, fire prevention): Report summarizes the previous quarter safety, security, fire work, analysis and processing incidents, inspection and analysis of accidents, the study identifies security precautions. (7) technology will work (including production technology will be ready) Report, summary of the month transformation, new product development, research, technology and production techniques to prepare the daily completion of the work plan, layout next month technical tasks, the study identifies the measures to solve the technical problem solutions. (8) production scheduling: Scheduling, balance the production schedule, study and solve various plant sections can not be resolved the major issues. (9) Division services will: Inspection, review, layout work. (10) Workshop's office: Inspection, review, layout work. (11) team will be: Inspection, review, layout work. (12) team (department) before the class will be: Commenting on the work of congenital, arranged day tasks and notes. 2 kinds of congress (1) the workers' congress: (2) shop (department) TUC (or workers' representative group will be): (3) Party Congress: (4) Congress members: (5) members of Congress CAST: (6) Enterprise Congress of the Association: 3. democratic management meeting (1) Plant Management Committee: (2) The director and party secretary, trade union chairman Joint Committee: (3) Production Management Committee: (4) Life Welfare Committee: 4 paper, the results conference. (1) Association of Science Annual Meeting: (2) Enterprise Association Annual Meeting: (3) political and ideological and political work of Annual Meeting: (4) Factory QC results conference: (5) scientific and technological achievements conference: (6) Information briefing: (7) Entrepreneurship results conference: Article arrangements for other meetings: Involving more than one workshop (departments) attended the meetings shall be held before the meeting or × × by the department in charge of the plant leadership approved, two were reported to do summary, arranged by the factories before they convened. Article factories, the plant should be regular meetings every Saturday and a variety of ad hoc meetings, meeting planning and preparation of a unified and balanced set issued to the factory and the workshop leaders, departments and related services personnel. Section 3 \ pnb0 where factories have been included in the accounting plan meetings for rescheduled, or other special circumstances need to arrange new meetings, the convener of 2 days in advance should be submitted to factories to adjust the meeting plan. Plants do not agree, no person shall disrupt the normal conference program easily. Section 3 \ pnb0 not prepared for, or repetitive, or have little role in the meeting, factories, the right to refuse arrangements. Article VIII for the same participants, content close to the time fits in a few meetings, factories hold the right to arrange the merger. Article IX session of the department must submit to the unified arrangement of the whole plant, small departments may not be placed in the same period the plant regular meeting was held, (the participants do not occur except in time of conflict) will be subject to the General Assembly should insist on a small, part to the overall principle. (D) to prepare the meeting Qiaopu electrical Article All presiding officers and the convener of the participants should make the preparations, respectively. (Including the agenda to be good, proposal, report summary outline, speaking points, the draft work plan, the Council decided to draft and implement the venue to prepare for sitting, tea tea, prizes, souvenirs, notify participants, etc.). [View Details]
Products Search
Contact Us
Contact Person:
Gavi ChenTel:
+86-0574-62166266- +86-15888180299
Fax:
+86-0574-62179799E-mail:
gavi@plug9.com
